Project 2 - V&V SW Analysis II

Overview of the Project:  Device Driver Write the device driver for MCP9808 Temperature Sensor. Probe function: Register the Platform device under driver/misc. Read function: It should send the i2c message to read the data from sensor and copy it to the user space. Alert pin connected to BBB as gpio interrupt. The temp…

  Overview of the Project:  Kconfig build system The module should be added to the Kernel configuration Kconfig build system with tristate option. Char driver should be of Open --> Only one user is allowed to open the device. Other users should be blocked. Read and write operation --> store the data to the dynamically…

Perform Static Code Review Analysis for “C:\**\LDRA_workarea\Examples\C_Testbed_examples\Testrain\Testrain.c” Generate Code review report and upload them.     Perform Integration testing by including all the .C files available in the folder location C:\**\LDRA_workarea\Examples\Toolsuite\Cashregister_6.0\…

1) Development of TFT Cluster Speedometer Software Component Cluster Instrument receives the signals from other ECU via CAN bus interface. It also receives commands from the driver via steering wheel buttons. The signals are then processed by the Cluster ECU, after which the Cluster ECU may send the vehicle information…

1) Wiper control system Develop Simulink/state flow model for wiper control system based on the given conditions. Description of Challenge: If the density of the rain is low, then wiper rotates with low speed & the output signal should be 100rpm If the density of the rain is medium, then wiper rotates with medium speed…

Q) Create a MATLAB model of electric car which uses a battery and a DC motor. Choose suitable blocks from Powertrain block set. Prepare a report about your model including following: Objectives:         1. System level configurations        2. Model parameters    …

  Part A:   1. Search and list out the total weight of various types of aircrafts.    2. Is there any difference between ground speed and air speed?   3. Why is it not recommended to use aircraft engine power to move it on the ground at Airport?    4. How an aircraft is pushed to runway…

1)   To calculate the energy required for braking during a defined driving cycle, you would need information about the vehicle's mass, velocity profile during the driving cycle, and braking efficiency. The basic formula to calculate kinetic energy is: Kinetic Energy= ½ mv2 where: m is the mass of the vehicle, v is the…

1) 1. A. Explain a MATLAB demo model named ‘Speed control of a DC motor using BJT H-bridge’.     B. Comment on the armature current shoot-up from the scope results.     C. Refer to the help section of ‘The Four-Quadrant Chopper DC Drive (DC7) block’. Compare it with the…

1.  Which types of power converter circuits are employed in electric and hybrid electric vehicle?        DC-DC Converters: Boost Converters: Increase the voltage from the low-voltage battery to the high-voltage level required by the electric motor. Buck Converters: Decrease the voltage for accessories or subsystems that…

/*  * GccApplication3.cpp  *  * Created: 23-11-2023 12:21:51 PM  * Author : OMKAR  */    #define F_CPU 8000000UL #include <avr/io.h> #include <avr/interrupt.h> #include <util/delay.h> #include <string.h> #include <stdlib.h>     #define LCD_Data_Dir…

  1) What is the difference between mapped and dynamic model of engine, motor and generator? How can you change model type?   1. Engine Models: Mathematical models: These models are used to represent the behavior of engines in a mathematical form. They can be either empirical (based on experimental data)…

1) For EV_defaults_in file, if cargo mass is 500 kg with all other default conditions, can the vehicle travel for 45 km with FTP drive cycle? Conclude your observations.   Observation: In this all values are default only cargo mass is change to 500kg before adding or increasing cargo mass distance traveled by…

Header, source file and project result attachted please cheack.

Ans: This test plan outlines the blackbox testing approach for a new mobile phone currently under development. The purpose of this test plan is to ensure that the mobile phone meets the specified requirements and functions as expected from a user's perspective. Objectives To verify that the mobile phone meets the defined…

Code: //Slave #include     int sig = 2;   //Assigning pin2 as sig for readabilty int duration, inches, cm;  static int avg;    void setup() { Serial.begin(9600); Wire.begin(8);    Wire.onRequest(distance);  }   void loop() { delay(50); }   void distance()     { pinMode(sig, OUTPUT);    digitalWrite(sig, LOW);  delay(5);…

Code:     /*  * GccApplication2.cpp  *  * Created: 05-09-2023 22:05:11  * Author : OMKAR  */    #include //we are using I/O registers of AVR #define F_CPU 16000000L // define the crystal frequency #include "avr/interrupt.h" // we are using external interrupt pin #include // delay function purpose #define sw_dir (PIND &…

Code: FOR MASTER :  //MASTER Arduino  #include void setup(){  pinMode(A1, INPUT);  Serial.begin(9600);  Wire.begin();  } void loop(){  float value=analogRead(A1);  signed int voltage=(value*5)/1024; // int temp=(voltage-0.5)*100;  Wire.beginTransmission(1);  Wire.write(voltage);  Wire.endTransmission();  delay(50);}  …

Code: #include #include #include using namespace std; enum class FuelType {    PETROL,    DIESEL,    GAS,    ELECTRIC}; class Vehicle {protected:    string make_;    string model_;    int year_;    int odometer_; public:    Vehicle(string make, string model, int year, int odometer)        : make_(make), model_(model),…

Code: #include #include #include enum GearState {    RETRACTED,    EXTENDED,    TRANSITIONING}; // switch statesenum SwitchState {    OPEN,    CLOSED}; // Function to simulate hydraulic pump controlvoid hydraulicControl(enum GearState *gear, const char *action) {    if (action == "extend") {        if (*gear == RETRACTED)…

Code: #include #include // Function for finding unionsvoid findUnion(int list1[], int size1, int list2[], int size2, int result[], int *resultSize) {    int i, j;    *resultSize = 0;     // Add elements from the first list to the result    for (i = 0; i < size1>        result[*resultSize] = list1[i];        (*resultSize)++; …