project:- %% first ploting of V VS I graph by importing data from execl sheet FID=xlsread('VI.xlsx');%opening of excel shhet V=FID(:,1);%storing value present in all rows and first coloumn I=FID(:,2);%storing value present in all rows and second coloumn Z=-17.3:.1:.9;%interpolation in the range of -17.3:0.1:0.9 Y=interp1(V,I,Z,"linear");%performing…

 Project - Speed Control of a Direct Current (DC) motor: Here the Speed control of a DC motor is either done manually by the operator or by means of an automatic control device. This is different to speed regulation where the speed is trying to be maintained or regulated against the natural change in speed due to…

1. Benchmark with present available cars in market for the following case. Monthly Kms including Madhurai return and office in bangalore = 1000 + (30*22) = 1660= 1700Kms (Approx). For the cost of vehicle I am assuming on road price to be considered. Also assuming Pughazhyendhii comes from middle class family, so he will…

Report Draft Analysis and Tooling Axis First observe the given class A surface to choose the tooling axis and select which axis is cover more phases of the given surface to draft.  After conform tooling axis Creat dummy line through tooling axis of class A surface. After dummy line, draw two lines from which surface…

  DESIGN AND DRAFT ANALYSIS OF SWITCH BEZEL:   OBJECTIVE: The objective of the project is to create the class B and C surface for the Base bracket with the given Class-A surface to design a component and carry Draft Analysis by creating the tooling direction for the given Class-A surface. DESIGN A COMPONENT…

AIM Create the Coin Holder Plastic component through the given Class-A surface.the tooling axis for the given Class-A Surface should be created meeting the requirements of the draft angle and at the end perform the Draft analysis on the model. the Thickness of the component to be 2.5 mm REPORT CLASS A SURFACE…

  Core & Cavity design Aim/Objectives: Create the Core and cavity blocks for the switch bezel designed in the earlier challenge. Steps Followed: Tooling Axis creation Checking Draft analysis for created tooling Axis Creating parting Surface Creating Core Side Creating cavity side. 1). Tooling Axis: Tooling axis is the…

  CREATION OF BUMPER BODY FROM A-SURFACE       AIM : To create a body of Bumper from the input given which was the A-surface of a Bumper. The created body should be a closed solid volume which should be feasible for manufacturing and Tooling. The draft angle and draft analysis of the component should…

AIM Create the component through the given Class-A surface.  the tooling axis for the given Class-A Surface should be created meeting the requirements of the draft angle and at the end perform the Draft analysis on the model. Create the rib and screw boss as by considering the design rules   CLASS A…

Aim : To create the class B surface, C surface and tooling axis also publish it as well as close surface the given door trims. Objectives : Create the Door Trim Plastic component through the given Class-A surface. To begin with, the tooling axis for the given Class-A Surface should be created meeting the requirements of…

Dog house design for the Door Trim:   Aim: Create the Dog House for the Door Trim considering the design rules and perform the draft analysis for class A and create the final close body component and perform the draft analysis. Objective: Create the Tooling axis  Design the class-B and class-C surfaces and…

DOOR TRIM LOWER Aim: To Create the Door trim lower component through the given Class-A surface. Objectives: • Creation of Tooling axis with appropriate draft angle. • Creation of other surfaces (eg, B and C surfaces) for creating a solid component. • Perform Draft analysis on Class A surface and Solid model hence created.…

A PILLAR DESIGN WITH MASTER SECTION MASTER SECTIION                    REFERENCE FOR CLASS A, CLASS B & CLASS C SURFACE.   CLASS A SURFACE                  check the surface quality         …

AIM :- To create assemblies of Quick return mechanism and CV joint and to also create 2D drawing of the given assemblies in CATIA.   ASSEMBLY :- Assembly modeling is a technology and method used by computer-aided design and product visualization computer software systems to handle multiple files that represent components…

UNDERBODY COATING   Underbody Coating is a sprayable coating, which protects the under surface of the vehicle from corrosion. Underbody coating provides long term protection from corrosion to car's underbody. It also protects parts like internal body panels, frame rails and other inner cavities that are not physically…

                                                HOOD DESIGN OF A CAR AIM :To design the…

Report On Section Modulus Calculation Of Hood Aim  To calculate the section modulus of the previously designed hood for analyzing its strength and also optimizing the design to see the difference in the bending strength of the hood. Higher the section modulus of a structure, the more the resistive it becomes…

                                                                     FINAL PROJECT   ISOMETRIC VIEW: FRONT VIEW: TOP VIEW: SIDE VIEW: FEATURE TREE:                              DETAILED REPORT ON FINAL PROJECT   AIM: To Create CAD model considering following inputs as like in OEM and tier1 companies a) Class A surface…

                                                       …

AIM: The aim of these project is to design fender and the main design requirements for Drip area, Bumper, A pillar and Sill mounting areas. Outer of car : Fender :             Fender is a front outer side member of a car which covers the wheel side. Fender purpose is to prevent sand, mud,…